Skip to content
Region and language EN
Region and language
0 items in cart

Cart

Your cart is empty.

Installation Tips6 min read

Subfloor and Wall Prep: The Step That Makes or Breaks Tile

What pros check under floors and behind walls before tile goes down: stiffness, flatness, self-leveling underlayment, backers, cracks and movement joints.

Subfloor and Wall Prep: The Step That Makes or Breaks Tile

Beautiful tile can fail in a year if the surface under it is wrong. Cracked tiles, hollow sounds, loose pieces and crumbling grout are almost always prep problems, not tile problems. That is why professional installers spend so much time before the first tile is set, and why prep is often the biggest line in a good tile quote.

This guide explains what pros check under floors and behind walls, in the order they check it. Use it to understand your estimate and to ask the right questions before work starts.

1. The floor must be stiff

Tile and grout are rigid. If the floor bends when you walk on it, the tile or the grout will crack. The industry measures this bending as deflection. The TCNA Handbook calls for a floor stiffness of at least L/360 for ceramic and porcelain tile and L/720 for natural stone, which means stone needs a floor twice as stiff.

Concrete slabs, common in Southern California homes, are usually stiff enough. Wood-framed floors, on second stories and raised foundations, depend on joist size, spacing and span. They often need an extra layer of plywood, especially before natural stone goes down. A bouncy floor is a warning sign that should be fixed before any tile is ordered.

2. The surface must be flat

Flatness is different from level. A floor can slope slightly and still be flat. What matters is that there are no humps or dips. The standard ANSI A108.02 sets these limits:

  • Tile with all sides under 15 in: no more than 1/4 in in 10 ft and 1/16 in in 1 ft.
  • Tile with any side 15 in or longer: no more than 1/8 in in 10 ft and 1/16 in in 2 ft.

Pros check with a long straightedge in several directions and mark the high and low spots. Small humps are ground down. For anything more than a few small dips, the best fix is a self-leveling underlayment over the whole floor, not hand-troweled patches. Thinset is not meant to fix an uneven floor. Using extra mortar to make up for dips leads to weak spots and lippage. Read more in our large-format tile guide.

Self-leveling underlayment: the best way to a flat floor

A self-leveling underlayment is a cement-based compound mixed with water into a pourable liquid. Poured over the floor, it flows out and settles into a flat, smooth surface on its own. Hand-floated patches and old screeds almost always leave waves that show up later as lippage and hollow tiles. A self-leveler gives the whole room one flat plane, which is exactly what long and large tile needs.

Why we prefer it before tile:

  • Flat across the whole room. It fills dips and covers small humps in one pour instead of patch by patch.
  • Fast. Many products can be walked on within hours and tiled the same day or the next, following the maker's data sheet.
  • Better mortar coverage. On a flat floor, the tile beds fully into the thinset, with fewer voids and fewer cracked tiles.
  • Less lippage. Tile edges line up because the floor under them does not wave.

How a pro pours it:

  • Clean the floor and remove dust, old adhesive and anything loose.
  • Seal off drains, gaps and openings, and set a foam strip or dam at the walls and doorways so the liquid stays in the room.
  • Prime the floor with the primer the maker requires. Primer helps the compound bond and stops pinholes and bubbles.
  • On wood floors, add metal lath or reinforcement and use a product rated for wood, if the maker requires it.
  • Mix each bag with the exact amount of water on the bag. Too much water weakens the surface.
  • Pour in one continuous flow from the far wall toward the door, and use a gauge rake and a spiked roller to spread it and release air.
  • Protect it from drafts and direct sun while it cures, then check it with a straightedge before tiling.

Each product has its own minimum and maximum thickness, cure time and approved substrates. Your installer should follow the data sheet for the exact product used. On a slab with moisture, choose an underlayment rated for those conditions.

3. Walls must be flat and plumb

Walls follow similar rules. They should be flat and plumb, especially behind long or glossy tile that shows every wave. Old plaster walls and bowed studs are common in older homes. Pros straighten studs, shim or replace boards, or skim the wall before tile goes up.

4. The right backer

Tile should not go straight onto drywall in wet areas or onto a single layer of wood subfloor. Common choices:

  • Cement backer board on floors and walls, set in thinset and fastened as the maker specifies, with taped and mortared seams.
  • Foam board systems for showers and walls, which are light, easy to cut and often already waterproof when installed as a complete system.
  • Uncoupling membranes over concrete or plywood, which help absorb small movement between the floor and the tile.
  • Concrete slabs can take tile directly if they are clean, cured, flat and free of active cracks.

In showers, the backer is only part of the story. The wall and floor also need a waterproofing layer. Read shower waterproofing basics.

5. Clean and sound

Thinset bonds to a clean, solid surface. The surface must be free of dust, paint, old adhesive, curing compounds and sealers that stop mortar from bonding. Old vinyl floors, carpet glue and loose tile come out first. Tiling over old tile is sometimes possible, but only when the old tile is fully bonded, flat and cleaned, and when the extra height works at doors and transitions. Your installer should check it tile by tile.

6. Cracks and moisture in concrete

Southern California slabs often have shrinkage cracks. A crack-isolation membrane over the crack, extending past it on each side, helps stop it from telegraphing through the new tile. Cracks that move or open over time, or where one side is higher than the other, need a structural check first.

Slabs on grade can also carry moisture from the ground. High moisture can weaken some adhesives and underlayments, so pros test new or suspect slabs and choose materials rated for the conditions.

7. Movement joints

Tile needs room to move as the building changes with temperature and humidity. Pros leave soft joints, filled with flexible sealant instead of grout, at the edges of the room, at changes of plane such as wall to floor and inside corners, and within large fields of tile. Areas exposed to direct sun, like floors by large windows and patios, need them more often. Skipping movement joints is a common cause of tiles tenting or popping up.

8. Height and transitions

Every layer adds height: underlayment, membrane, mortar and tile. Plan where the new floor meets wood, carpet or another tile, and check that doors, appliances and the dishwasher will still fit. Our trims and transition pieces help finish those edges cleanly.

A quick prep checklist

  • Is the floor stiff enough for the tile you chose, especially for stone?
  • Is the floor or wall flat to the standard for your tile size?
  • Is the right backer or membrane planned for the room?
  • Is the surface clean, sound and free of old adhesive?
  • Are cracks treated and movement joints planned?
  • Have heights and transitions been checked?

Common questions

  • Can I tile directly over plywood? Not over a single layer in most cases. Most installation methods call for backer board or a membrane over the plywood.
  • Can I tile over old tile? Sometimes, if it is fully bonded and flat. It adds height, and any hidden problems underneath stay there.
  • Why is prep so expensive? Because it decides how long the tile lasts. Fixing a failed floor costs far more than preparing it right once. Read DIY or hire a tile pro.

Need help?

Our crew checks and prepares every surface before installation, so your tile lasts. Browse floor tile and send us your project for a free estimate.

Shop Floor Tile →

More Installation Tips

All Tips & Guides →