Shower Waterproofing: Membranes, Slope and Drains
Tile and grout are not waterproof. The real protection is the membrane and slope behind them. Here is how a lasting tiled shower is built.
A tiled shower looks solid, but tile and grout are not waterproof. Cement grout is porous, and water gets behind the tile every day. What keeps your walls, framing and subfloor dry is the waterproofing system underneath. When it is done right, a shower can last for decades. When it is skipped or rushed, leaks, loose tiles and mold can show up within a few years, often in a room below or inside the wall where you cannot see them.
This guide explains how a lasting tiled shower is built, from the framing to the last bead of sealant, so you know what to expect from your installer.
The two jobs of a shower system
- Stop water from reaching the wall framing, the subfloor and the rooms around the shower.
- Move water that gets under the tile back to the drain, so it never sits.
Every method below does both jobs. The difference is where the waterproof layer sits and how water reaches the drain.
Two ways to build a shower floor
- Traditional mortar bed with a liner. A sloped mortar layer, called a pre-slope, goes under a waterproof liner. A second mortar bed goes on top, and the tile is set on that. Water that soaks through the top bed runs along the liner to weep holes in the drain. This method has a long track record when built carefully.
- Bonded surface membrane. The waterproof layer goes directly under the thinset, just below the tile, using a liquid, sheet or foam board system with a matching drain. Very little water soaks into the mortar, so the shower dries faster. Many crews prefer this method today.
Both can work well. What matters is that the method is followed exactly as the maker describes it, with the parts made for that system.
Waterproofing membranes
Bonded membranes for tile are tested to the ANSI A118.10 standard. Common types:
- Liquid-applied membranes, rolled or brushed on in two or more coats to a set thickness, with fabric in corners and seams.
- Sheet membranes, bonded with thinset, with overlapped and sealed seams and preformed corners.
- Foam board systems, light panels that are waterproof when their joints and fasteners are sealed as the system requires.
The membrane must be continuous. Inside and outside corners, the niche, the bench, the curb and every pipe and valve need the maker's corner pieces and seals. A single gap is enough for a leak. Thickness matters too: liquid membranes are checked with a wet film gauge or by coverage rate, not by eye.
What does not belong in a shower
Regular drywall and moisture-resistant green board are not shower backers. They soften when wet. The California Residential Code requires a smooth, hard, nonabsorbent surface, such as tile, over a suitable backer on shower walls to a height of at least 6 ft above the floor. Our guide to subfloor and wall prep covers the right backers.
Another common mistake is doubling up: a plastic vapor barrier behind the board and a surface membrane on top. That can trap moisture inside the wall. Follow one system, not two.
Slope to the drain
The shower floor must slope toward the drain so water never sits. The usual slope is about 1/4 in per foot. With a traditional floor, the pre-slope under the liner needs the same slope, not just the top layer.
- Center drains need a four-way slope, like a shallow funnel. Small tiles and mosaics bend with those planes, which is why they work best there.
- Linear drains let the floor slope in one direction, toward one wall or the entry. Large tiles fit that single plane, and the floor can run without a curb for a curbless, accessible shower.
Read choosing shower tile for the tile sizes and finishes that work on shower floors.
Flood test before tile
Before tiling, pros plug the drain and fill the shower floor with water, then check for any drop in level or leaks. Many crews and inspectors expect a test of about 24 hours. It is the cheapest insurance you can buy: fixing a membrane before tile costs a few hours, fixing it after costs a new shower. In many cities the pan is part of the permit inspection, see shower remodel codes in California.
Niches, benches and curbs
Every niche and bench adds corners to seal. The bottom of a niche and the top of a bench should slope slightly toward the shower so water runs off. Plan niches between studs on an inside wall, not on an outside wall, and size them to the tile so you avoid thin cuts. Curbs get the membrane over the top and down the outside, with a slight slope inward.
Steam showers
Steam showers need more. Vapor drives into the walls and ceiling under pressure, so they need a membrane rated for continuous steam use, a sloped ceiling so condensation runs down, and a sealed door. Ask for a steam-rated system by name.
Finishing details
Use flexible sealant, not grout, at inside corners, at changes of plane and where the tile meets the tub, the glass or a different material. Those joints move, and grout cracks there. Glass doors should be fastened so the screws do not break the membrane, or with sealed fasteners.
After installation, let the grout and sealant cure as their makers require before the first shower. Then keep the shower ventilated and wipe or squeegee the walls to cut down on hard water marks, see remove hard water stains.
Warning signs in an existing shower
- Grout that stays dark long after a shower.
- Loose or hollow-sounding tiles, especially near the floor.
- Cracked grout or sealant at corners.
- Peeling paint, stains or a musty smell outside the shower or on the ceiling below.
These usually mean water is getting behind the tile. Regrouting may hide the symptom for a while, but the fix is often a rebuild of the waterproofing.
Common questions
- Is grout sealer enough to waterproof a shower? No. Sealer slows staining in grout. Waterproofing comes from the membrane or liner underneath.
- Do I need to waterproof the walls outside the spray zone? The code sets the minimum, but most crews waterproof the full shower walls, and the ceiling in steam showers.
- Can a shower be built over an existing tub area? Yes, often, but the floor framing, drain and waterproofing all change. It is a full shower build, not a tile swap.
Need help?
Shower waterproofing is the part of the job you never see and the part that matters most. Our crew builds showers from the pan up and flood tests before tile. Browse shower tile and ask for a free estimate.