Lippage is when the edge of one tile sits higher than the edge of the next. You can feel it with bare feet, hear a sock catch on it and see it when light comes in low across the floor from a window or a patio door. With big and long tiles it is the most common complaint after installation, and it is almost always preventable.
This guide covers large-format tile and slabs, which at Tile Total means 48 x 48 in and larger, and also the popular long sizes such as 12 x 24 in and 24 x 48 in. The installation standard applies the same strict rules to any tile with a side of 15 in or more, so everything below applies to all of them.
Why big tiles show lippage
- The surface is not flat enough. A small tile follows a gentle dip. A large tile bridges it, so one edge ends up high.
- Tiles have a slight curve. Long tiles can be slightly higher in the middle or at the ends from firing. This is called warpage, and the tile standard allows a small amount of it.
- Mortar is uneven or does not fully support the tile, so it settles while it cures.
- The layout offset puts the high center of one tile next to the low edge of another.
- Light makes it look worse. Low, raking light from large windows or wall lights at floor level casts a shadow at every tiny step.
How much lippage is acceptable?
Some lippage is normal. The standard ANSI A108.02 allows about 1/32 in between neighboring tiles with joints narrower than 1/4 in, and about 1/16 in with joints 1/4 in and wider, plus the warpage the tile itself is allowed to have. Natural stone and handmade tile are expected to vary more. If your floor is within these limits but you can still see shadows, lighting is often the cause, not the installation.
1. Start flat
For tiles with any side 15 in or longer, the surface should vary no more than 1/8 in in 10 ft and 1/16 in in 2 ft. Fixing the floor first is faster and cheaper than fighting lippage tile by tile. Pros check with a long straightedge, grind high spots and fill low ones with a patch or a self-leveling underlayment. Thinset is not a leveling material. Read subfloor and wall prep for the full process.
2. Use the right mortar and trowel
Choose a mortar rated for large and heavy tile, and a trowel size that gives full support for the tile and the surface. Pros:
- Comb the mortar in straight, parallel lines, usually along the short side of the tile, so air can escape when the tile is pressed down.
- Back-butter every tile with a thin, flat coat so the back is fully wetted.
- Press and slide the tile across the ridges to collapse them.
- Lift a tile now and then to check coverage: at least 80% in dry areas and 95% in wet areas and with natural stone, with the edges and corners fully supported.
Our guide to choosing thinset and grout explains the mortar types.
3. Leveling systems help, but do not fix bad prep
Clips and wedges, or caps and spin knobs, hold neighboring edges at the same height while the mortar cures. On large and long tiles they help a lot, and most good crews use them. But they only pull edges together. They cannot fill hollow spots or make up for a wavy floor, and forcing a tile down onto a high spot can crack it later.
4. Watch the offset
For rectangular tiles with a side longer than 18 in, the standard calls for an offset of no more than 1/3 of the tile length, unless the maker says otherwise. A classic 1/2 running bond puts the slightly higher center of one tile beside the ends of the next. For a 24 x 48 in tile, a 1/3 offset means shifting each row by 16 in or less. Some makers allow other offsets for their tile, so check the product guidance before you choose a layout. See our tile layout patterns guide.
5. Grout joint width
Rectified tiles have ground edges and allow thin joints, but the standard calls for a joint no narrower than 1/16 in, and many makers ask for more on long tiles. A joint that is too thin leaves no room for normal size and warpage differences and makes every height step easier to see. Ask your installer what joint they recommend before you settle on a look.
6. Mind the light
Before tile goes down, think about where light comes from. Large windows, glass doors and wall-mounted lights near the floor create raking light. In those rooms, a matte or honed finish, a slightly wider joint and laying the long side of the tile toward the window all help hide small height differences.
7. Handle slabs with care
Slabs and other true large-format tiles need two or more installers, suction cup lifters or a carrying frame, and a mortar layer that supports the whole back. They bend if lifted wrong and can crack on a high spot. Our large-format tile guide covers delivery and handling.
Before installation checklist
- Is the surface flat to 1/8 in in 10 ft and 1/16 in in 2 ft?
- Is the mortar rated for large and heavy tile, with the right trowel?
- Is the offset planned at 1/3 or less, or as the maker allows?
- Is the joint width agreed?
- Will a leveling system be used?
- Are all boxes from one batch, opened and blended before setting?
Common questions
- Can lippage be fixed after installation? Only by removing and resetting the affected tiles. Grinding porcelain removes its surface and changes how it looks.
- Is some lippage on stone normal? Yes. Tumbled and handmade surfaces vary by nature and are judged differently.
- Do leveling clips mean prep can be skipped? No. They help a flat floor stay flat while it cures, nothing more.
Need help?
Big tile rewards an experienced crew. Ours handles leveling, mortar and layout from start to finish. Browse floor tile and request a free estimate.