How Much Tile to Order: Waste Allowance by Layout
Order too little and you may never match the batch again. Here is how to measure your room and how much extra to add for straight, diagonal and herringbone layouts.
Running short on tile in the middle of a project is one of the most frustrating problems in a remodel. Tile is made in batches, and a new batch can differ slightly in shade, tone and size. Ordering a few more boxes weeks later rarely gives a perfect match. That is why getting the quantity right the first time matters.
The good news: the math is simple. You need four numbers: the area, the extra for cuts, the coverage of one box, and a few spares. This guide walks through each step with real examples.
Step 1: Measure the area
Measure in feet and round each measurement up to the next half foot.
- Floor: multiply length by width. For an L-shaped room, split it into rectangles and add them up.
- Wall: multiply width by height. Subtract only large openings such as doors and windows. Leave small openings like outlets in the total.
- Shower: measure each wall separately, add the floor, then add the curb, the niche and the bench, top and sides.
- Backsplash: measure the length of each run and multiply by the height, usually from the countertop to the bottom of the upper cabinets.
Example: a 9 x 7 ft bathroom floor is 63 sq ft. If the vanity is freestanding and the tile runs under it, include that area too.
Step 2: Add extra for cuts
Every layout needs some tiles to be cut at the walls, around the toilet, at doorways and around pipes. The pieces you cut off are often too small to reuse, and a few tiles may break during cutting. Use these typical allowances:
- Straight layout: add about 10%
- Offset or brick layout: add about 10%
- Diagonal layout: add about 15%
- Large-format tile (24 in and up): add about 15%, because each broken or miscut tile is a big loss
- Herringbone and chevron: add about 15%, sometimes more in small rooms
- Mosaic sheets: about 5% is usually enough, because sheets cut easily between tiles
Small rooms with many corners need more extra than big open floors, because a larger share of tiles is cut. If your room has a lot of angles, pipes or built-ins, move up one step. Our tile layout patterns guide shows how each pattern looks.
For the 63 sq ft bathroom with a straight layout: 63 x 1.10 = 69.3 sq ft.
Step 3: Round up to full boxes
Tile is sold by the full box. Divide the total by the coverage of one box, then always round up.
If one box covers 15.5 sq ft: 69.3 / 15.5 = 4.47, so you order 5 boxes, which gives you 77.5 sq ft.
Our product pages do this math for you. Enter your area, choose the extra percentage and the calculator shows the square footage and the number of boxes. Box coverage is listed on each product, so you never have to guess.
A full bathroom example
Here is how the numbers add up for a typical small bathroom with a tiled shower:
- Floor: 63 sq ft + 10% = 69.3 sq ft
- Shower walls: three walls, 5 ft, 3 ft and 3 ft wide, all 8 ft high = 88 sq ft + 10% = 96.8 sq ft
- Shower floor mosaic: 3 x 5 ft = 15 sq ft + 5% = 15.75 sq ft
- Niche and curb: about 6 sq ft, ordered in the wall tile
If the floor and walls use different tiles, run the box math separately for each product. Always round up per product, not for the room as a whole.
Step 4: Do not forget trim
Trim is counted by length, not by area. Measure every edge that will show: outside corners, the edge of a niche, the top of a wainscot, the curb and any place where tile stops in the open. Add those lengths in feet, divide by the length of one trim piece, and round up. Add one or two extra pieces for corners and cuts.
Step 5: Keep a few spare tiles
After the job, keep at least a few tiles, or a full box for large floors, from the same batch. If a tile ever cracks, you will have a perfect match. Read more in why you should keep spare tile.
Why ordering extra up front saves money
Because tile is sold by the full box, and batches can differ in shade and caliber, a short order is the expensive mistake. A new batch may not match the floor you already installed, and the crew may have to wait for delivery. Ordering the right amount in one go keeps the whole project in one batch and on schedule.
Common mistakes
- Measuring only the open floor and forgetting the area under a vanity that will be tiled
- Forgetting the shower curb, niche and bench
- Counting trim by area instead of measuring the edges in feet
- Rounding the whole room up once instead of rounding each product up to full boxes
- Ordering the last few boxes later from a different batch
Common questions
- Is 10% always enough? For straight layouts in simple rooms, yes. Go to 15% for diagonal, herringbone and large-format tile, or for rooms with many corners.
- Should I order extra if a pro installs the tile? Yes. Professional installers still need cuts. A good installer will check your quantity before you order.
- Can I order a sample before I buy all the boxes? Many tiles offer a sample on request. Check the product page, and see our tile specs guide to compare products.
Need help?
Not sure about your numbers? Send us your room sizes and layout idea and we will check the quantity for you before you order. Start by browsing all tile.